- MENU
- Home
-
Categories
- Air conditioner (switchgear cabinet)
- Base/base element (switchgear cabinet)
- Case for component installation with modular spacing 19 inch
- Climate control door (enclosure/cabinet)
- Climate control side panel (enclosure/cabinet)
- Component for arrangement / baying system (switchgear cabinet)
- View all categories
- Accessories/spare parts for domestic switching devices
- Accessories/spare parts for socket outlets/plugs with protective contact
- Cable entry
- Combination of switch/push button with socket outlet
- Control element/cover plate for domestic switching devices
- Controller for light controlling system
- View all categories
- Accessories/spare parts for earthing and lightning
- Accessories/spare parts for surge protection data networks/MCR-technology
- Accessories/spare parts for surge protection power supply systems
- Air-termination equipment for lightning protection
- Base for air termination systems lightning protection
- Basic element for surge protection device
- View all categories
- AC-power supply
- Accessories/spare parts for command devices
- Accessories/spare parts for electronic motor control and protection device
- Accessories/spare parts for emergency stop pull cord switch
- Accessories/spare parts for frequency controller
- Accessories/spare parts for low-voltage switch technology
- View all categories
- Accessories/spare parts for underfloor installation ducting systems
- Bend for underfloor installation ducting systems
- Coupler for underfloor installation duct
- Cover for underfloor installation duct flush floor open
- Cover plate for installation units
- End piece for underfloor installation duct
- View all categories
- Request Quote
- How RFQ Works
- Contact Us
- FAQ
View larger
Images are for illustrative purposes only. Please refer to data sheet for details
SB-8ES6D8AA700S 1315007 PHOENIX CONTACT M40, Conect. plug. to be apar. front wall, series: SB, Swivel angle,..
SB-8ES6D8AA700S
1315007
PHOENIX CONTACT
1 Pcs.
M40, Conect. plug. to be apar. front wall, series: SB, Swivel angle, shielded: yes, for standard lock and SPEEDCON, No. of poles: 6+4+4+PE, 6-pole data element, Direction of rotation: Standard, contact connection type: Female, Crimp connection, Axial O-ring, 4x Ø4.2
M40, Conect. plug. for apar. wall front, SB, Swivel angle, shielded: yes, for standard and SPEEDCON locking, No. of poles: 6+4+4+PE, 6-pole data element, Direction of rotation: Standard, contact type: Female, Crimped connection, Axial O-ring, 4x Ø4,2
M40, Device connector front mounting, series: SB, angled rotatable, shielded: yes, for standard and SPEEDCON interlock, No. of pos.: 6+4+4+PE, 6-pos. data element, Direction of rotation: Standard, contact connection type: Socket, Crimp connection, Axial O-ring, 4x Ø4,2
Cables > Circular connector, mounting (without cable)
Field Device Connectors (FDC)
Product condition, packaging, certifications and applicable manufacturer warranty terms are confirmed with the quotation.
More info
▲Technical data
Notes
| General | Order crimp contacts separately |
| Safety note | |
| Safety note | WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. |
| • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. | |
| • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. | |
| • The products are suitable for applications in plant, controller, and electrical device engineering. | |
| • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. | |
| • Assembled products may not be manipulated or improperly opened. | |
| • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). | |
| • When using the product in direct connection with third-party manufacturers, the user is responsible. | |
| • For operating voltages > 50 V AC, conductive connector housings must be grounded | |
| • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector | |
| • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product | |
| • Only use tools recommended by Phoenix Contact | |
| • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. | |
| • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products | |
| • Operate the connector only when it is fully plugged in and interlocked. | |
| • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. | |
| • Observe the minimum bending radius of the cable. Lay the cable without twisting it. | |
| • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). | |
Product properties
| Product type | Circular connectors (device side) |
Connector
| Insulating body | |
| Connection method | Crimp connection |
| Contact switching type | Socket |
| Application | Hybrid |
| Number of positions | 15 |
| Direction of rotation | Standard |
| Connection profile | 6+4+4+PE, 6-pos. data element |
| Contact diameterPower contacts | 3.6 mm |
| Litz wire cross-sectionPower contactsmin. | 1 mm² |
| Litz wire cross-sectionPower contactsmax. | 16 mm² |
| Rated currentPower contacts | 70 A |
| Note | at an ambient temperature of 15°C, see derating curve |
| Rated voltage | 630 V AC |
| Rated surge voltage | 6 kV |
| Overvoltage category | III |
| Degree of pollution | 3 |
| Rated voltage (II/3) power contact | 850 V DC |
| Rated voltage (III/3) power contact | 630 V AC |
| Contact diameterSignal contacts | 1 mm |
| Litz wire cross-sectionSignal contactsmin. | 0.06 mm² |
| Litz wire cross-sectionSignal contactsmax. | 1.5 mm² |
| Nominal current per signal contact | 8 A |
| Note | for max. connection cross section |
| Rated surge voltage | 6 kV |
| Overvoltage category | III |
| Degree of pollution | 3 |
| Rated voltage (III/3) signal contact | 500 V |
| Contact diameter Data contacts | 0.6 mm |
| Litz wire cross-section Data contacts min. | 0.08 mm² |
| Litz wire cross-section Data contacts max. | 0.25 mm² |
| Rated current per data contact at 25°C | 2 A |
| Note | for max. connection cross section |
| Rated surge voltage | 1.5 kV |
| Installation height | 2000 m |
| Housing | |
| Housing material | Turned parts: copper zinc alloy (CuZn), die-cast parts: zinc (GD-Zn) |
| Type of locking | for standard and SPEEDCON interlock |
| Pg screw connection | none |
| Degree of protection (plugged in) | IP68/IP69K |
| Thread type | M40 |
Environmental and real-life conditions
| Ambient conditions | |
| Ambient temperature (operation) | -40 °C ... 115 °C |
| Feature Name | Feature Value |
|---|---|
| Number of data contacts (EF012232) | 0 |
| Number of power contacts (EF012216) | 0 |
| Ambient temperature (EF002386) | -40 °C |
| Type of locking (EF000208) | Other |
| With protective conductor (EF007468) | No |
| Screened (EF000881) | No |
| With status indication (EF001602) | No |