PHOENIX CONTACT REL-FO/L-230AC/1X21 REL-FO/L-230AC/1X21 1308317 PHOENIX CONTACT Plug-in miniature relay, FASTON connection, 1 switch, status ind.. View larger
Images are for illustrative purposes only. Please refer to data sheet for details

REL-FO/L-230AC/1X21 1308317 PHOENIX CONTACT Plug-in miniature relay, FASTON connection, 1 switch, status ind..

REL-FO/L-230AC/1X21

1308317

PHOENIX CONTACT

10 Pcs.

Plug-in miniature relay, FASTON connection, 1 switch, status indication: LED (yellow), Input voltage: 230 V AC Plug-in miniature relay, FASTON connection, 1 changeover contact, status display: Yellow LED, Input voltage: 230 V AC

Automation > Switching relay
Industrial Relays

Product condition, packaging, certifications and applicable manufacturer warranty terms are confirmed with the quotation.

Request a Quote

Pricing and availability are confirmed for each enquiry. Send this part and we will reply with price and lead time.

Request Quote

Product Overview

Utilized for galvanic isolation and signal multiplication, a Phoenix Contact Plug-in miniature relay bridges the gap between low-power control electronics and higher-voltage field loads. These electromechanical devices ensure safe and dependable switching cycles inside modern control systems.

Pricing, availability and lead time are confirmed per enquiry through an RFQ.

  • Product type: Single relay
  • Product family: ESSENTIAL edition
  • Operating mode: 100% operating factor
  • Mechanical service life: approx. 3x 10 7 cycles
  • Relay type: Electromechanical relay
  • Overvoltage category: II
  • Pollution degree: 3
  • Maximum power dissipation for nominal condition: 0.9 W
  • Test voltage (Winding/contact): 5 kV rms (50 Hz, 1 min., winding/contact)
  • Test voltage (): 1 kV rms (50 Hz, 1 min., open contact)
  • Rated surge voltage: 2.5 kV
  • Coil side Nominal input voltage U N: 230 V AC
  • Input voltage range: 184 V AC ... 253 V AC
  • Mains frequency: 50/60 Hz
  • Drive and function: monostable
  • Drive (polarity): non-polarized

More info

▲
Technical data

Notes
GeneralDo not use to separate SELV/PELV circuits from other circuits, because safe isolation is not guaranteed. (applies to the optocoupler variants)
GeneralThe system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.

Product properties
Product typeSingle relay
Product familyESSENTIAL edition
Operating mode100% operating factor
Mechanical service lifeapprox. 3x 107cycles
Relay typeElectromechanical relay
Insulation characteristics: Air clearances and creepage distances between the power circuits
InsulationBasic insulation
Overvoltage categoryII
Pollution degree3

Electrical properties
Maximum power dissipation for nominal condition0.9 W
Test voltage (Winding/contact)5 kVrms(50 Hz, 1 min., winding/contact)
Test voltage ()1 kVrms(50 Hz, 1 min., open contact)
Air clearances and creepage distances between the power circuits
Rated insulation voltage250 V AC
Rated surge voltage2.5 kV

Input data
Coil side
Nominal input voltage UN230 V AC
Input voltage range184 V AC ... 253 V AC
Mains frequency50/60 Hz
Drive and functionmonostable
Drive (polarity)non-polarized
Typical input current at UN4.5 mA (50 Hz)
Input power dissipation for UN1 W
Typical response time2 ms ... 15 ms
Typical release time range5 ms ... 20 ms
Status displayYellow LED
Coil resistance24100 Ω ±10 %

Output data
Switching
Contact switching type1 changeover contact
Type of switch contactSingle contact
Contact materialAgSnO
Maximum switching voltage250 V AC/DC
Minimum switching voltage5 V (100 mA)
Limiting continuous current12 A
Maximum inrush current24 A (20 ms, N/O contacts)
Inrush current, minimum100 mA (5 V)
Interrupting rating (ohmic load) max.288 W (24 V DC)
360 W (30 V DC)
3000 VA (250 V AC)

Connection data
Cross section AWG(converted acc. to IEC)
Connection methodFASTON connection

Dimensions
Width13 mm
Height31.1 mm
Depth30 mm

Environmental and real-life conditions
Ambient conditions
Degree of protection (Relay)RT II (Relay)
Degree of protection (Installation location)IP54 (Installation location)
Ambient temperature (operation)-40 °C ... 70 °C
Ambient temperature (storage/transport)-40 °C ... 70 °C
Altitude≤ 2000 m

Standards and regulations
Standards/regulationsIEC 61810-1
IEC 60664-1
Air clearances and creepage distances between the power circuits
Standards/regulationsIEC 60664-1

Mounting
Mounting positionany

Product Datasheet

Electrica Online Product Datasheet Prepared from the current product description, catalog data and structured technical attributes.