PHOENIX CONTACT REL-FO/L-110DC/2X21 REL-FO/L-110DC/2X21 1308307 PHOENIX CONTACT Plug-in miniature relay, FASTON connection, 2 switched contacts,.. View larger
Images are for illustrative purposes only. Please refer to data sheet for details

REL-FO/L-110DC/2X21 1308307 PHOENIX CONTACT Plug-in miniature relay, FASTON connection, 2 switched contacts,..

REL-FO/L-110DC/2X21

1308307

PHOENIX CONTACT

10 Pcs.

Plug-in miniature relay, FASTON connection, 2 switched contacts, status indication: LED (yellow), Input voltage: 110 V DC Plug-in miniature relay, FASTON connection, 2 changeover contacts, status display: Yellow LED, Input voltage: 110 V DC

Automation > Switching relay
Industrial Relays

Product condition, packaging, certifications and applicable manufacturer warranty terms are confirmed with the quotation.

Request a Quote

Pricing and availability are confirmed for each enquiry. Send this part and we will reply with price and lead time.

Request Quote

Product Overview

A Phoenix Contact REL-FO/L-110DC/2X21 single relay is an electromechanical switching device utilized in industrial automation environments to isolate control circuits and manage secondary loads. This component interfaces low-level controller outputs with higher-voltage field instrumentation to ensure reliable sequential logic execution. Pricing, availability, and lead time are confirmed per enquiry through an RFQ.

  • General: The outputs are not suitable for switching different outer conductors.
  • Product type: Single relay
  • Product family: ESSENTIAL edition
  • Operating mode: 100% operating factor
  • Mechanical service life: approx. 5x 10 7 cycles
  • Relay type: Electromechanical relay
  • Overvoltage category: II
  • Pollution degree: 3
  • Maximum power dissipation for nominal condition: 0.9 W
  • Test voltage (Winding/contact): 5 kV rms (50 Hz, 1 min., winding/contact)
  • Test voltage (Changeover contact/changeover contact): 3 kV rms (50 Hz, 1 min., changeover contact/changeover contact)
  • Test voltage (): 1 kV rms (50 Hz, 1 min., open contact)
  • Rated surge voltage: 2.5 kV
  • Coil side Nominal input voltage U N: 110 V DC
  • Input voltage range: 77 V DC ... 121 V DC
  • Drive and function: monostable

More info

▲
Technical data

Notes
GeneralDo not use to separate SELV/PELV circuits from other circuits, because safe isolation is not guaranteed. (applies to the optocoupler variants)
GeneralThe outputs are not suitable for switching different outer conductors.
GeneralThe system installer must ensure the touch protection of the product (at voltages > 25 V AC/60 V DC). The product is a built-in device without protection against direct contact.

Product properties
Product typeSingle relay
Product familyESSENTIAL edition
Operating mode100% operating factor
Mechanical service lifeapprox. 5x 107cycles
Relay typeElectromechanical relay
Insulation characteristics: Air clearances and creepage distances between the power circuits
InsulationBasic insulation
Overvoltage categoryII
Pollution degree3

Electrical properties
Maximum power dissipation for nominal condition0.9 W
Test voltage (Winding/contact)5 kVrms(50 Hz, 1 min., winding/contact)
Test voltage (Changeover contact/changeover contact)3 kVrms(50 Hz, 1 min., changeover contact/changeover contact)
Test voltage ()1 kVrms(50 Hz, 1 min., open contact)
Air clearances and creepage distances between the power circuits
Rated insulation voltage250 V AC
Rated surge voltage2.5 kV

Input data
Coil side
Nominal input voltage UN110 V DC
Input voltage range77 V DC ... 121 V DC
Drive and functionmonostable
Drive (polarity)non-polarized
Typical input current at UN6 mA
Input power dissipation for UN0.66 W
Typical response time9 ms
Typical release time3 ms
Status displayYellow LED
Coil resistance18870 Ω ±10 %

Output data
Switching
Contact switching type2 changeover contacts
Type of switch contactSingle contact
Contact materialAgSnO
Maximum switching voltage250 V AC/DC
Minimum switching voltage5 V (10 mA)
Limiting continuous current8 A
Maximum inrush current16 A (20 ms, N/O contacts)
Min. switching current10 mA (5 V)
Interrupting rating (ohmic load) max.192 W (24 V DC)
240 W (30 V DC)
2000 VA (250 V AC)

Connection data
Cross section AWG(converted acc. to IEC)
Connection methodFASTON connection

Dimensions
Width13 mm
Height31.1 mm
Depth29 mm

Environmental and real-life conditions
Ambient conditions
Degree of protection (Relay)RT II (Relay)
Degree of protection (Installation location)IP54 (Installation location)
Ambient temperature (operation)-40 °C ... 70 °C
Ambient temperature (storage/transport)-40 °C ... 70 °C
Altitude≤ 2000 m

Standards and regulations
Standards/regulationsIEC 61810-1
IEC 60664-1
Air clearances and creepage distances between the power circuits
Standards/regulationsIEC 60664-1

Mounting
Mounting positionany

Product Datasheet

Electrica Online Product Datasheet Prepared from the current product description, catalog data and structured technical attributes.