View larger
RIF-1-RPT-LV-24AC/2X21 2903333 PHOENIX CONTACT Pre-assembled relay module with push-in connection, consistin..
RIF-1-RPT-LV-24AC/2X21
2903333
PHOENIX CONTACT
10 Pcs.
Automation > Switching relay
Industrial Relays
Product condition, packaging, certifications and applicable manufacturer warranty terms are confirmed with the quotation.
Request a Quote
Pricing and availability are confirmed for each enquiry. Send this part and we will reply with price and lead time.
Request QuoteProduct Overview
The Phoenix Contact pre-assembled relay module (part number RIF-1-RPT-LV-24AC/2X21) serves as an interposing interface component used to match signal levels, amplify control outputs, and provide galvanic isolation in industrial control gear. These modular assemblies streamline panel wiring while protecting sensitive controllers from electrical transients. Pricing, availability, and lead time are confirmed per enquiry through an RFQ.
- Complete with socket: Yes
- With detachable clamps: No
- With LED indication: Yes
- Rated control supply voltage AC 50 Hz: 19.2 V
- Rated control supply voltage AC 60 Hz: 19.2 V
- Voltage type for actuating: AC
- Drive, polarization: Polarized
- Drive, switching attitude: Mono stable
- Number of contacts as normally closed contact: 0
- Number of contacts as normally open contact: 0
- Number of contacts as change-over contact: 2
- Type of switch contact: Single contact
- With forced-guided contacts: No
- Material of contact surface: Untreated
- Nominal current: 0.033 A
- Degree of protection (IP): IP20
More info
▲Dimensions
| Width | 16 mm |
|---|---|
| Height | 93 mm |
| Depth | 75 mm |
Ambient conditions
| Ambient temperature (operation) | -40 °C ... 50 °C |
|---|---|
| Ambient temperature (storage/transport) | -40 °C ... 85 °C |
Coil side
| Nominal input voltage UN | 24 V AC |
|---|---|
| Input voltage range in reference to UN | see diagram |
| Typical input current at UN | 33 mA |
| Typical response time | 3 ms ... 12 ms |
| Typical release time range | 3 ms ... 20 ms |
| Coil voltage | 24 V AC |
| Protective circuit | Varistor |
| Operating voltage display | Yellow LED |
Contact side
| Contact type | 2 PDT |
|---|---|
| Contact material | AgNi |
| Maximum switching voltage | 250 V AC/DC |
| Minimum switching voltage | 5 V (at 10 mA) |
| Min. switching current | 10 mA (At 5 V) |
| Maximum inrush current | 12 A (20 ms, N/O contact) |
| Limiting continuous current | 8 A (see diagram) |
| Interrupting rating (ohmic load) max. | 192 W (at 24 V DC) |
| 96 W (at 48 V DC) | |
| 60 W (at 60 V DC) | |
| 44 W (at 110 V DC) | |
| 57 W (at 220 V DC) | |
| 2000 VA (for 250 V AC) | |
| Switching capacity in acc. with DIN VDE 0660/IEC 60947 | 2 A (at 24 V, DC13) |
| 0.2 A (at 250 V, DC13) | |
| 3 A (at 24 V, AC15) | |
| 3 A (at 120 V, AC15) | |
| 3 A (at 250 V, AC15) |
Connection data input side
| Connection name | Coil side |
|---|---|
| Connection method | Push-in connection |
| Stripping length | 8 mm |
| Conductor cross section solid | 0.14 mm² ... 1.5 mm² |
| Conductor cross section flexible | 0.14 mm² ... 1.5 mm² |
| 0.14 mm² ... 1 mm² (Ferrule with plastic sleeve) | |
| 0.14 mm² ... 1.5 mm² (Ferrules without plastic sleeve) | |
| Conductor cross section AWG | 26 ... 16 |
General
| Type of note | Notes on operation |
|---|---|
| Note | FBS 2-6... plug-in bridge for the input side (A2) and FBS-2-8... plug-in bridge for the output side (11/21) |
| Test voltage relay winding/relay contact | 4 kVrms(50 Hz, 1 min.) |
| Test voltage PDT/PDT | 2.5 kVrms(50 Hz, 1 min.) |
| Operating mode | 100% operating factor |
| Degree of protection | IP20 (Relay socket) |
| RT III (Relay) | |
| Mechanical service life | Approx. 107cycles |
| Standards/regulations | DIN EN 50178 |
| IEC 62103 | |
| Pollution degree | 2 |
| Overvoltage category | III |
| Mounting position | any |
| Assembly instructions | In rows with zero spacing |