View larger
VC-AML 5 1607523 PHOENIX CONTACT Contact insert
VC-AML 5
1607523
PHOENIX CONTACT
5 Pcs.
Connectors > Accessories/spare parts for industrial connectors
Field Device Connectors (FDC)
Product condition, packaging, certifications and applicable manufacturer warranty terms are confirmed with the quotation.
Request a Quote
Pricing and availability are confirmed for each enquiry. Send this part and we will reply with price and lead time.
Request QuoteProduct Overview
Phoenix Contact contact insert, part number VC-AML 5 1607523, organizes modular power and signal distribution within heavy-duty industrial connector housings. Contact inserts are fundamental components in modular industrial plug systems, facilitating rapid connection and disconnection of complex machinery.
Pricing, availability and lead time are confirmed per enquiry through an RFQ.
- General: Connectors may only be connected/disconnected when under no load.
- Product type: Contact insert
- Product family: VARIOCON
- Series: VC-M
- Type: VC3
- Number of positions: 5
- Connection profile: 4+PE
- Number of module slots: 4
- Data management status Article revision: 02
- Insulation characteristics Degree of pollution: 3
- Rated voltage (II/2): 1000 V
- Rated voltage (III/2): 1000 V
- Rated voltage (III/3): 690 V
- Nominal voltage ATD: 690
- Rated surge voltage: 6 kV
- Rated surge voltage (II/2): 8 kV
More info
▲| General | Connectors may only be connected/disconnected when under no load. |
| Safety note | |
| Safety note | WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property. |
| • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible. | |
| • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product. | |
| • The products are suitable for applications in plant, controller, and electrical device engineering. | |
| • When operating the connectors in outdoor applications, they must be separately protected against environmental influences. | |
| • Assembled products may not be manipulated or improperly opened. | |
| • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products). | |
| • When using the product in direct connection with third-party manufacturers, the user is responsible. | |
| • For operating voltages > 50 V AC, conductive connector housings must be grounded | |
| • Ensure that the protective or functional ground has been properly connected. | |
| • VDE 0100/1.97 § 411.1.3.2 and DIN EN 60 204/11.98 § 14.1.3 are applicable when combining several circuits in a cable and/or connector | |
| • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product | |
| • Only use tools recommended by Phoenix Contact | |
| • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product. | |
| • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products | |
| • Operate the connector only when it is fully plugged in. | |
| • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards. | |
| • Observe the minimum bending radius of the cable. Lay the cable without twisting it. | |
| • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). | |
| Product type | Contact insert |
| Product family | VARIOCON |
| Series | VC-M |
| Type | VC3 |
| Number of positions | 5 |
| Connection profile | 4+PE |
| Number of module slots | 4 |
| Data management status | |
| Article revision | 02 |
| Insulation characteristics | |
| Degree of pollution | 3 |
| Rated voltage (II/2) | 1000 V |
| Rated voltage (III/2) | 1000 V |
| Rated voltage (III/3) | 690 V |
| 690 V | |
| Nominal voltage ATD | 690 |
| Rated surge voltage | 6 kV |
| Rated surge voltage (II/2) | 8 kV |
| Rated surge voltage (III/2) | 8 kV |
| Rated surge voltage (III/3) | 8 kV |
| Rated surge voltage | 6 kV |
| Rated current | 63 A |
| 70 A | |
| 63 A | |
| Nominal voltage UN | 690 V |
| Connection method | PCB connection |
| Dimensional drawing | |
| Width | 60 mm |
| Height | 23 mm |
| Length | 35.6 mm |
| Color | light grey |
| Color of the housing part | gray |
| Material | Polyamide |
| Flammability rating according to UL 94 | V0 |
| Insulating material group | I |
| Housing material | PA |
| Contact material | E-Cu 58 |
| Contact surface material | hard-silver plated |
| Contact carrier material | PA |
| Halogen-free | yes |
| Mechanical data | |
| Insertion/withdrawal cycles | ≥ 50 |
| Ambient conditions | |
| Ambient temperature (operation) | -40 °C ... 100 °C |