View larger
REL-FO/LRC-230AC/1X21/MS 1308323 PHOENIX CONTACT Plug-in miniature relay with mechanical switching position ..
REL-FO/LRC-230AC/1X21/MS
1308323
PHOENIX CONTACT
10 Pcs.
Automation > Switching relay
Industrial Relays
Product condition, packaging, certifications and applicable manufacturer warranty terms are confirmed with the quotation.
Request a Quote
Pricing and availability are confirmed for each enquiry. Send this part and we will reply with price and lead time.
Request QuoteProduct Overview
A Phoenix Contact REL-FO/LRC-230AC/1X21/MS plug-in miniature relay provides robust switching performance for commercial and industrial electrical panels. Electromechanical relays of this type are routinely installed to handle repetitive switching cycles and provide secure circuit separation.
Pricing, availability and lead time are confirmed per enquiry through an RFQ.
- Product Type: Individual relay
- Product Family: ESSENTIAL edition
- Operating Mode: Working time 100%
- Mechanical service life: approx. 3x 10 7 operations
- Relay Type: Electromechanical relay
- Surge Category: Ii
- Degree of pollution: 3
- Maximum Dissipated Power with Nominal Condition: 1 W
- Test Voltage (Winding/Contact): 5 kV Eff (50 Hz, 1 min., winding/contact)
- Test Voltage (): 1 kV Eff (50 Hz, 1 min., open contact)
- Dimensioning Transient Voltage: 2.5 kV
- Arousal Side Nominal Input Voltage U N: 230 V AC
- Input Voltage Range: 184 V AC ... 253 V AC
- Mains Frequency: 50/60 Hz
- Drive switching behavior: monostable
- Drive (polarity): bipolar
More info
▲| General | They should not be used to separate SELV/PELV electrical circuits from other electrical circuits, as safe separation is not guaranteed. (valid for optocoupler variants) |
| General | Protection against accidental contact of the article (with voltages > 25 V AC/60 V DC) must be ensured by the system manufacturer. This is an assembly device without protection against direct contact. |
| Product Type | Individual relay |
| Product Family | ESSENTIAL edition |
| Operating Mode | Working time 100% |
| Mechanical service life | approx. 3x 107operations |
| Relay Type | Electromechanical relay |
| Insulation Properties: Leak Lines and Air Gaps Between Circuits | |
| Isolation | Basic Insulation |
| Surge Category | Ii |
| Degree of pollution | 3 |
| Maximum Dissipated Power with Nominal Condition | 1 W |
| Test Voltage (Winding/Contact) | 5 kVEff(50 Hz, 1 min., winding/contact) |
| Test Voltage () | 1 kVEff(50 Hz, 1 min., open contact) |
| Creepage lines and air gaps between circuits | |
| Sizing Insulation Voltage | 250 V AC |
| Dimensioning Transient Voltage | 2.5 kV |
| Arousal Side | |
| Nominal Input Voltage UN | 230 V AC |
| Input Voltage Range | 184 V AC ... 253 V AC |
| Mains Frequency | 50/60 Hz |
| Drive switching behavior | monostable |
| Drive (polarity) | bipolar |
| Typical Input Current to UN | 4.5 mA (50 Hz) |
| Input Dissipated Power with UN | 1 W |
| Typical Reaction Time | 2 ms ... 15 ms |
| Typical Open Time Range | 5 ms ... 20 ms |
| Protection Circuit | RC Module |
| Status Indication | Yellow LED |
| Coil Resistance | 24100 Ω ±10 % |
| Commute | |
| Contact Switching Type | 1 switch |
| Switching Contact Type | Simple Contact |
| Contact Material | AgSnO |
| Maximum Switching Voltage | 250 V AC/DC |
| Minimum Activation Voltage | 5 V (100 mA) |
| Constant Current Limit | 12 A |
| Maximum connection current | 24 A (20 ms, open contact) |
| Minimum Shut-Off Current | 100 mA (5 V) |
| Maximum Breaking Power (Ohmic Load) | 288 W (24 V DC) |
| 360 W (30 V DC) | |
| 3000 VA (250 V AC) | |
| Connection type | FASTON Connection |
| Width | 13 mm |
| Height | 31.1 mm |
| Depth | 35 mm |
| Environmental conditions | |
| Protection Index (Relay) | RT II (Relay) |
| Protection Index (Installation Location) | IP54 (Mounting Location) |
| Ambient Temperature (Service) | -40 °C ... 70 °C |
| Ambient Temperature (Storage/Transport) | -40 °C ... 70 °C |
| Altitude | ≤ 2000 m |
| Standards/Specifications | IEC 61810-1 |
| IEC 60664-1 | |
| Creepage lines and air gaps between circuits | |
| Standards/Specifications | IEC 60664-1 |
| Position for mounting | discretionary |